All Reviews

I used the Planted bracket with Sparco steel universal side mounts, to put a Corbeau FX1 in my 2015 Honda Fit. The Planted bracket is noticably nicer than the Corbeau, for nearly the same price. The multiple hole options on the bracket allowed me to get the seat perfectly adjusted. I'm planning to upgrade to Planted aluminum side mounts next. I apologize for my filthy autox car lol

Fits so perfectly it’s incredible 10/10 recommendations for anyone looking for quality work, amazing customer service and amazing welds clean install

Was excited to see a company that made brackets for our 1977 Celica GT Drift build. Quick test fit, before we build the cage and everything lines up great!

Love the products perfectly fit to the car, well built and excellent costumer service did not take long to receive 10/10

I purchased the Planted Technology seat adapters for installing new Recaro Sporter seats into my 2002 Porsche 996 Turbo. They are well made but had to drill new holes to make them fit.
Once installed they are solid and secure.

The fit is perfect and the finish is good. Could not have asked for a better seat bracket for my 2024 Polaris slingshot. This was the first time hearing about your company and you guys produced a great product.

Firstly, I must say that the customer service is top notch with the but I'm sorry to say this but the driver side bracket does not at all quite right. The two rear holes needed to be elongated left to right to allow the OEM bolts to thread in and the front didn't even come close to fitting. I had to cut them off and re-weld them into the correct placement. Also, the base itself is too wide that it needs to be shaved down from touching the transmission tunnel. And this is with the factory carpet installed. With all that taken care of, the base does sit the chair as close to the floor without removing the humps.

Again, the customer service is fantastic but the jig for the driver side and passenger side are both terrible. I know this is a pretty niche chassis but it shouldn't have fitment issues this bad. none of the holes line up and the base position is way to high! The Sparco seats I have are set to its lowest height my head is about less than a inch away from the headliner. The FC3S chassis still has the sunroof but that shouldn't be an excuse to have it that tall. That is without a helmet by the way. Again I had to cut a re-weld the base to a much lower position for the seats to fit better.

These seat brackets were exactly what I needed and the quality exceeded my expectations. But more importantly, the Planted Technologies customer service is excellent. I made an error when ordering what I needed, and before they shipped my order, they caught the error and contacted me to verify what I actually needed.

Fitment on chassis holes are not good and require modification

Can confirm success installing both Sparco R100 and Braum Elite-S Sport seats into my 23 WRX using these bases. I used grade 8 1/2" hardware for the seatbelt buckle and Sparco's install hardware to mount the sliders to the base. The seatbelt buckle wire seems to have a clip that grounds to the base, and I forced it to spread onto the thicker Planted base. Might be beneficial for future revisions of the Planted base to include a dedicated spot for this ground clip.

I was a little apprehensive of the cost of the brackets at first but upon unboxing and installing I’d buy them again in a heartbeat. Thick and built like a tank. Bolted right up to my Recaro Expert M’s and then to my floor. Thanks for a great product!

The bolt slots were not wide/diverse enough even for a Recaro seat. There is also not enough space between the riser and the car floor mount with requires short bolts or cutting existing bolts. If the same increase in height is applicable I would recommend going with the entire seat bracket riser vs these.

Well made product but positioned the seat too high for my application. Even with the sliders removed I don’t fit in the car with my helmet on
Wish I found the brey Krause mounts before buying these

These bolted right up with no modifications needed. I really appreciate quality workmanship for products like these. They were well constructed, solid, and lined up perfectly. I would buy these again in a heartbeat for matching up with my Recaro Specialist seats and Recaro sliders.

Didn’t fit

Didn’t fit as intended

I was going to make custom brackets for my seats, I didn’t expect that something was available, and of great quality.

Good quality over all but one of the tabs wasn’t welded on straight. Didn’t cause enough of an issue to return the item.

Well worth the money especially compared to competitors options. These brackets are very strong and solid. They bolted right up and I tried to shake them to see how strong they were and they didn’t budge. Bolted right up to my fixed back seat. Love the fact that it has the seatbelt buckle mounting point. Very high quality. Professional welds. I have no doubt in my mind about these. It may be more than the cheap eBay brackets but trust me it is well worth it and will keep you safe.

I bought both the driver and passenger brackets for my RSX. The fitment is perfect. My specific brackets make one bolt had a pain to install, but it’s not fault to the bracket. The design of these accommodates oem Recaro sliders (and several others), and to make the seats sit as low as possible, one bolt is hard to tighten as it sits under the surface area of the bracket itself.

These are much sturdier than the PCI brackets they replaced and have more adjustability. If you have replacing your factory seats in your RSX, choose these, you will not be dissapoinyrd.

The bracket hardly fits, only three holes lined up and we had to grind the fourth hole to make it fit

Only company that makes these for 1999 Benz SLK230, has both seatbelt brackets for install. All other only have 1. Great Brackets

Fit in my Saab like it said it would.

Works perfectly, and quick arriving very pleased. I would use these in any application.